Tsm Race - 36mm Hubs w/ ARP Studs and Bearings

36mm Tsm Race Hubs w/ ARP Studs and Bearings

Includes

• Tsm Race
• ARP Wheel Studs
• Bearings

Read below for more information…..

Tsm Race 36mm Swap Hubs provide the SOLUTION for upgrading to OEM Honda/Acura “36mm” axles in high powered 1988-2005 Civics, 1990-2001 Integras, 1988-1991 CRX’s, and 2009-2013 Fits.  Perfect for K-Swaps; but can also be used with high output B, D, F, H, and J-Swaps.

Like breaking axles?  Level 1 Swap Axles just don't cut the mustard with a rating of only 200WHP.  Whose K-Swap doesn't make over 200WHP?!?  Level 2.9 Swap Axles are not much better of an alternative as they still utilize the smaller Civic/Integra/CRX axle spline and will run a good $800-$1200 for a pair.  This is where OEM Honda/Acura “36mm” axles fit in.  They utilize a substantially larger axle spline which allows them to handle higher horsepower and torque outputs, yet they are extremely cost effective.  This larger axle spline is observed in chassis such as the Acura RSX-S, Honda 06+ Civic Si, and Honda Prelude.  Unfortunately, this larger spline is unable to be installed directly into OEM Civic, Integra, or CRX hubs, so that is where our Tsm Race 36mm Swap Hubs come into play.  Tsm Race are modeled almost exactly after the OEM Honda/Acura hubs they replace, except that the splines now match that of the larger “36mm” axles.  Side Note: Internet forum terminology has named the larger OEM spline axles “36mm”.  We have conformed to that terminology as not to confuse others.  However; for educational and axle identification purposes, “36mm” is actually the socket size used for the axle nut of these larger spline axles.  The larger spline diameter in reality measures 29.50mm on these axles.

• CNC turned out of billet high strength chrome-moly steel
• Oil quenched and tempered
• Maintains OEM rotor-centric attributes
• Designed for the larger OEM 29.50mm axle spline (36mm axle nut socket)
• OEM “36mm” axles have proven time and again to easily sustain 500+ WHP

Use TSM Race P/N: TSM01 to replace factory OEM Honda hub P/N: 44600-S04-980 found on 70% of USDM 1992-2000 Honda Civic models.  These vehicles use a 38mm I.D. wheel bearing and also have factory brake discs which measure 240mm (or 9.44 inch) O.D.

Use TSM Race P/N: TSM02 to replace factory OEM Honda/Acura hub P/N: 44600-S04-A00 found on ALL USDM 1994-2001 Acura Integra models (excluding Type-R) and 30% of USDM 1992-2000 Honda Civic models.  These vehicles use a 43mm I.D. wheel bearing and also have factory brake discs which measure 262mm (or 10.31 inch) O.D.

If you are uncertain which OEM Honda hubs are used on your 1992-2000 Honda Civic knuckles, simply measure the I.D. (inner diameter) of your wheel bearing or the O.D. (outer diameter) of your original factory brake disc and compare with the above. 

Use TSM RACE P/N: TSM03 to replace factory OEM Honda hubs found on all USDM 1988-1991 Honda Civic and CRX models.  These hubs use a 38mm I.D. wheel bearing.

Install wheel hubs per the procedure called out in the Honda/Acura Service Manual.  As instructed, ALWAYS use new wheel bearings for hub replacement as its inevitable you will be placing side loads never intended for the wheel bearings when having to remove the old hub.  WHEEL BEARING TYPE DOES NOT CHANGE WITH OUR HUBS; SIMPLY USE REPLACEMENT WHEEL BEARINGS FOR THE OEM KNUCKLE ASSEMBLY BEING USED.

NOTE: We recommend using only OEM Honda/Acura axles.  Trust us; a used and rusty 80,000 mile OEM Honda/Acura salvage yard axle will outlast the generic auto parts store replacement axles by tenfold!